- 您现在的位置：买卖IC网 > Sheet目录500 > PT204-6B (Everlight Electronics Co Ltd)PHOTOTRANSISTOR 3MM NPN BK RAD
DATASHEET
3mm Phototransistor
PT204-6B
Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.
?
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4.
Cleaning
?
?
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5.
Heat Management
?
?
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6.
ESD (Electrostatic Discharge)
?
?
?
?
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of
friction between LEDs during storage and handing.
7.
Other
?
?
?
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
9
www.everlight.com
:2
Revision Copyright ?
LifecyclePhase:
Release Rev.2
2010, Everlight All Rights Reserved. Release Date : JUNE.5.2013. Issue No:DPT-0000293 Date:2013-06-07 16:41:04.0
Expired Period: Forever
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PT204-6C
PHOTOTRANSISTOR 3MM NPN CLR RAD
PT222J2
THERMISTOR 2252 OHM +/-0.20 C
PT2559B-F
PHOTOTRANSISTOR SIDE FACE BK RAD
PT2559B/L2/H2-F
PHOTOTRANSISTOR SIDE FACE BK RAD
PT26-21B/TR8
PHOTOTRANSISTOR FLAT BK MINI SMD
PT26-21C/TR8
PHOTOTRANSIST FLAT CLR MINI SMD
PT26-51B/TR8
PHOTOTRANSIST 1.6MM BK MINI SMD
PT28-21B/TR8
PHOTOTRANSIST 1.3MM FLAT BK SMD
相关代理商/技术参数
PT204-6B_06
制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:3mm Phototransistor T-1
PT204-6C
功能描述:PHOTOTRANSISTOR 3MM NPN CLR RAD RoHS:是 类别:传感器，转换器 >> 光学 - 光电检测器 - 光电晶体管 系列:- 标准包装:1,200 系列:- 电压 - 集电极发射极击穿（最大）:30V 电流 - 集电极 (Ic)（最大）:1mA 电流 - 暗 (Id)（最大）:100nA 波长:880nm 视角:24° 功率 - 最大:100mW 安装类型:通孔 方向:顶视图 封装/外壳:径向
PT2047
制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | NPN | 80V V(BR)CEO | 5A I(C) | TO-202
PT-205
功能描述:WIRE TIE PUSHBUTTON NAT POLY RoHS:是 类别:线缆，导线 - 管理 >> 扎带 系列:PT 标准包装:1,000 系列:PAN-TY® 导线/缆线捆扎带类型:标准，锁定 线束直径:5.00"（127.00mm） 长度:1.46'（444.40mm） 宽:0.190"（4.80mm） 安装类型:自由悬挂 张力强度:50 磅（22.7 kg） 特点:- 材质:尼龙 包装:每包 1000 个 颜色:灰
PT205112
制造商:Hubbell Wiring Device-Kellems 功能描述:Non-Metallic Plugtrak 6 FT Base And Cover
PT205112P
制造商:Hubbell Wiring Device-Kellems 功能描述:Non-Metallic Portable Plugtrak
PT205112TR
制造商:Hubbell Wiring Device-Kellems 功能描述:PLUGTRAK TAMPER RESIST 20A 5FT NONMETAL
PT205115
制造商:Hubbell Wiring Device-Kellems 功能描述:PLUGTRAK, 5', 20A, 1CIRC, 4 DUP